搜索结果：Powders

Ion sputtering from loose powders remains poorly understood despite its relevance to planetary science and industry. We developed a multiscale Monte Carlo model to simulate sputtering from powders, using a higher-fidelity approach for the target geometry compared to voxel-based methods. Simulating Kr+ ions impacting Cu powders and flat slabs, we show that sputtering from loose powders differs markedly from that of flat slabs or rough surfaces. The main differences are: (1) for incident angles a > 0 degree relative to the bulk normal, the escaping sputtering yield is dominated by backward-directed ejecta for all ion energies; (2) for a < 60 degrees, the yield peaks toward the ion-beam origin, similar to the opposition effect seen in optical observations of airless bodies; (3) the angular distribution peak is half or less than that of a flat slab; (4) as ion energy increases, no evolution occurs from primary to secondary knock-on sputtering in the ejecta angular distribution. We attribute these behaviors to the powders interconnected voids. Ions penetrate these voids and sputter underlying grains; the ejecta then preferentially escape toward the ion-beam origin, where shadowing

The mechanisms of fast low-temperature Spark Plasma Sintering (SPS) of W + 10% wt. Ni powders were investigated. The powder compositions were obtained in two methods: (i) by mixing W and Ni powders in a specified ratio (hereinafter referred to as W + Ni); (ii) by Ni deposition on the surface of submicron W particles allowing the formation of particles with a core W - shell Ni structure (hereinafter referred to as W@Ni). To reduce the concentrations of oxygen and oxides, the powders were annealed in hydrogen. The solid-phase sintering was performed at various temperatures (1000-1150°C), pressures (40-80 MPa), heating rates (50-500°C/min), and isothermal holding times (0-20 min). The sintering temperatures corresponded to the onset of intense dissolution of W in Ni. The samples had high relative density and small grain sizes. The activation energy of SPS of the mixed powders was close to the one of the grain boundary diffusion. The key mechanism for the compaction of W@Ni particles in the SPS process is Coble creep. The increasing of the sintering temperature was shown to lead to an increase in the solubility of W in Ni and, consequently, to an increase in the number of secondary Ni4

Reactive aluminum (Al) alloy powders are promising for advanced manufacturing, joining, and energetic applications, yet scalable routes that couple controlled reactivity with safe handling remain limited. While nanoscale Al powders ignite readily, their agglomeration, handling, and safety limit broad deployment. Here, we manufacture micron-sized Al-based powders produced by ultrasonic atomization (UA), targeting a balance of enhanced reactivity and process robustness. Binary systems (AlCu, AlSi, AlMg) and pure Al were synthesized, and their morphology, phases present, thermal stability, and oxidation behavior were characterized using XRD, SEM, and DTA/TGA in an Ar/O2 environment. We show that alloy selection and UA-controlled microstructure can modify the native Al2O3 passivation, alter oxidation pathways, and shift thermal onsets/exotherms. The results establish a manufacturing-forward framework for designing micron-sized powders with tunable ignition/oxidation behavior.

Lactose is the major component of milk powders and is normally found to be in a glassy/amorphous state. During storage, lactose is known to participate in physicochemical processes, including crystallization on the surface and reaction with proteins such as $β$-lactoglobulin. Lactose needs to be mobile to participate in such processes. However, there is a lack of evidence of its mobility in milk powders. In this study, we demonstrate that some of the lactose becomes mobile when milk powders are exposed to humid air $-$ an inappropriate storage condition. This mobility is evidenced by peaks in magic angle spinning $^{1}\mathrm{H}$ NMR spectra of milk powders in the range of 3.5 ppm to 4.0 ppm, which stem from lactose molecules displaying considerable rotational mobility. These signals have a longitudinal relaxation time constant T1 similar to that of mobile water according to 2D T1$-δ(^{1}\mathrm{H})$ experiments under magic angle spinning. Furthermore, 2D $^{1}\mathrm{H}-^{13}\mathrm{C}$ HSQC magic angle spinning experiments of skim milk powder demonstrate the same fingerprint as that of lactose in the solution, confirming our observations.

Shear cell tests have been conducted on twenty different lactose powders, most of which commercially available for oral or inhalation purposes, spanning a wide range of particle sizes, particle morphologies, production processes. The aims of the investigation were: i) to verify the reliability of the technique in evaluating and classifying the flowability of powders; ii) to understand the connection between the flowability of a powder and the morphological properties of its particles; iii) to find a general mathematical relationship able to predict the yield locus shape given the particle size, shape and consolidation state of a lactose powder. These aspects and their limitations are detailed in the manuscript together with other interesting findings on the stick-slip behavior observed in most of the lactose powders examined.

When amorphous molecular powders are exposed to high humidity levels or temperatures, the particle viscosity increases due to plasticization, promoting the formation of sinter bridges between pairs of particles in contact. Over time, these bridges facilitate particle agglomeration, eventually leading to the formation of a macroscopic cake that alters the mechanical properties and affects product quality. In this work, we model the caking process of amorphous powders subjected to a temperature shock as a bond percolation problem and investigate how particle bed heterogeneities influence the percolation threshold and, consequently, the expected caking times. Our findings indicate that a slight dispersion in particle size lowers the percolation threshold compared to a monodisperse bed or random percolation in polydisperse systems. Furthermore, we show that the expected caking time exhibits a non-monotonic behavior with the size dispersion, initially decreasing for low dispersion values and increasing for higher values. These results provide insights into the role of the particle size distribution on the caking dynamics of amorphous molecular powders

Micron-scale metal-based composite powders are promising for energetic applications due to their tailored ignition and combustion properties. In particular, ball-milled Al/Zr composites exhibit lower ignition thresholds than pure aluminum, driven by exothermic intermetallic formation reactions and have demonstrated enhanced combustion properties. However, the extent to which this heat release governs ignition and combustion remains unclear, especially when progressively removed through annealing. To systematically investigate this effect, we synthesized Al/Zr powders (3Al:Zr, Al:Zr, and Al:3Zr at%) via ball milling, annealed them in argon up to 1000 C to partially complete the formation reactions, and characterized their ignition and combustion behavior. Ignition thresholds were measured using a hot wire method across different environments, while high-speed hyperspectral imaging tracked single-particle burn durations and temperatures. A convolutional neural network (CNN)-based method was developed to quantify the frequency of microexplosions. Results show that annealing - and thus reducing available reaction heat - increases ignition thresholds, most significantly for Al-rich comp

H2-H2O redox cycling of iron powder beds at 650-800 °C offers a compact, safe, economical hydrogen storage method, but sintering-induced capacity loss has stalled its scalability for decades. Here, we show that adding redox-active tungsten to Fe powders solves this problem in static powder beds: Fe-25W (at%) alloyed powder self-foams during redox cycling via W gas-phase transport, increasing porosity and preserving capacity. In a custom automated reactor, a kilogram-scale powder bed reversibly stores 42g H2 and sustains 96+/-3% capacity utilization over 30 redox cycles. Temperature-resolved in-situ X-ray diffraction reveals a chemical-vapor-transport-mediated self-foaming mechanism that redistributes W to refine the microstructure, complemented by a contact-barrier stabilization mechanism during high-temperature holds. Partial-capacity cycling up to 90 cycles further confirms sintering resistance under incomplete redox conditions. These results establish Fe-W powder beds as a robust, scalable, and compact platform for safe, stationary hydrogen storage.

Controlling the size of powder particles is pivotal in the design of many pharmaceutical forms and the related manufacturing processes and plants. One of the most common techniques for particle size reduction in process industry is powder milling, whose efficiency relates to the mechanical properties of powder particles themselves. In this work, we first characterize the elastic and plastic response of different pharmaceutical powders by measuring their Young modulus, the hardness and the brittleness index via nano-indentation. Subsequently, we analyze the behavior of those powder samples during comminution via jet-mill at different process conditions. Finally, the correlation between single particle mechanical properties and milling process results is illustrated; the possibility to build a predictive model for powder grindability, based on nano-indentation data, is critically discussed

Powder bed additive manufacturing processes such as laser powder bed fusion (LPBF) or binder jetting (BJ) benefit from using fine (D50 $\leq20~μm$) powders. However, the increasing level of cohesion with decreasing particle size makes spreading a uniform and continuous layer challenging. As a result, LPBF typically employs a coarser size distribution, and rotating roller mechanisms are used in BJ machines, that can create wave-like surface profiles due to roller run-out. In this work, a transverse oscillation kinematic for powder spreading is proposed, explored computationally, and validated experimentally. Simulations are performed using an integrated discrete element-finite element (DEM-FEM) framework and predict that transverse oscillation of a non-rotating roller facilitates the spreading of dense powder layers (beyond 50% packing fraction) with a high level of robustness to kinematic parameters. The experimental study utilizes a custom-built mechanized powder spreading testbed and X-ray transmission imaging for the analysis of spread powder layers. Experimental results generally validate the computational results, however, also exhibit parasitic layer cracking. For transverse

For the purpose of applying laws or principles originated from thermal systems to granular athermal systems, we may need to properly define the critical temperature concept in granular powders. The conventional environmental temperature in thermal systems is too weak to drive movements of particles in granular powders and cannot function as a thermal energy indicator. For maintaining the same functionality as in thermal systems, the temperature in granular powders is defined analogously and uniformly in this article. The newly defined granular temperature is utilized to describe and explain one of the most important phenomena observed in granular powders, the jamming transition, by introducing jamming temperature and jamming volume fraction concepts. The predictions from the equations of the jamming volume fractions for several cases like granular powders under shear or vibration are in line with experimental observations and empirical solutions in powder handlings. The goal of this article is to establish similar concepts in granular powders, allowing granular powders to be described with common laws or principles we are familiar with in thermal systems. Our intention is to build

The widespread application of metal additive manufacturing (AM) is limited by the ability to control the complex interactions between the energy source and the feedstock material. Here we develop a generalizable process to introduce nanoscale grooves to the surface of metal powders which increases the powder absorptivity by up to 70% during laser powder bed fusion. Absorptivity enhancements in copper, copper-silver, and tungsten enables energy efficient manufacturing, with printing of pure copper at relative densities up to 92% using laser energy densities as low as 82 J/mm^3. Simulations show the enhanced powder absorptivity results from plasmon-enabled light concentration in nanoscale grooves combined with multiple scattering events. The approach taken here demonstrates a general method to enhance the absorptivity and printability of reflective and refractory metal powders by changing the surface morphology of the feedstock without altering its composition.

To investigate excess-hydrolysis of titanium alkoxides, TiO2 powders were fabricated from titanium-tetra-isopropoxide using 6:1 and 100:1 H2O:Ti (r) ratios. Powders were dried and fired at a range of temperatures ( up to 800 C). Hydroxylation and organic content in powders were characterised using ATR-FTIR, laser Raman microspectroscopy, and elemental microanalysis; surface area and pore size distribution were evaluated using N2 gas adsorption; phase composition was analysed using XRD and laser Raman microspectroscopy; and crystallite size was evaluated by XRD, TEM and SEM. Results showed near-complete hydrolysis in a predominantly aqueous medium (r = 100), resulting in precipitated crystalline powders exhibiting brookite and anatase, which begin to transform to rutile below 500 C. Powders precipitated in a predominantly organic medium (r = 6) underwent partial hydrolysis, were highly porous and exhibited an amorphous structure, with crystallisation of anatase occurring at 300 C and transformation to rutile beginning at 500 to 600C.

Experiments with low-Z powder injection in DIII-D high confinement discharges demonstrated increased divertor dissipation and detachment while maintaining good core energy confinement. Lithium (Li), boron (B), and boron nitride (BN) powders were injected in high-confinement mode plasmas ($I_p=$1 MA, $B_t=$2 T, $P_{NB}=$6 MW, $\langle n_e\rangle=3.6-5.0\cdot10^{19}$ m$^{-3}$) into the upper small-angle slot (SAS) divertor for 2-s intervals at constant rates of 3-204 mg/s. The multi-species BN powders at a rate of 54 mg/s showed the most substantial increase in divertor neutral compression by more than an order of magnitude and lasting detachment with minor degradation of the stored magnetic energy $W_{mhd}$ by 5%. Rates of 204 mg/s of boron nitride powder further reduce ELM-fluxes on the divertor but also cause a drop in confinement performance by 24% due to the onset of an $n=2$ tearing mode. The application of powders also showed a substantial improvement of wall conditions manifesting in reduced wall fueling source and intrinsic carbon and oxygen content in response to the cumulative injection of non-recycling materials. The results suggest that low-Z powder injection, including

A three-dimensional model of a partially melted powder bed with particles stochastically distributed in size and space coordinates has been developed. Numerical simulation of temperature distributions in stainless steel AISI 316L and Al-12Si powders in vacuum, air and argon has been performed to analyze unsteady heat transfer in a porous medium. The numerical model demonstrates a large effect of heat transfer through the gas phase in case of powders with low thermal conductivities like stainless steels. At the porosity level of 65\% and above, the mechanism of heat transfer drastically changes and a linear dependence of thermal conductivity on porosity frequently used in literature becomes incorrect. The effects of the consolidation coefficient and size distribution on effective heat transfer in powders are discussed. The obtained dependencies of the effective thermal conductivity on porosity and the consolidation coefficient could be used in additive manufacturing applications.

Powders are a special class of granular matter due to the important role of cohesive forces. The flow behavior of powders depends on the flow states and stress and is therefore difficult to measure/quantify with only one experiment. In this study, the most commonly used characterization tests that cover a wide range of states are compared: (static, free surface) angle of repose, the (quasi-static, confined) ring shear steady state angle of internal friction, and the (dynamic, free surface) rotating drum flow angle are considered for free flowing, moderately and strongly cohesive limestone powders. The free flowing powder gives good agreement among all different situations (devices), while the moderately and strongly cohesive powders behave more interestingly. Starting from the flow angle in the rotating drum and going slower, one can extrapolate to the limit of zero rotation rate, but then observes that the angle of repose measured from the heap is considerably larger, possibly due to its special history. When we stretch the ring shear test to its lowest confining stress limit, the steady state angle of internal friction of the cohesive powder coincides with the flow angle (at free

Synthesis and research of the properties of boron nitride powders and BN powders with additives produced under effect of concentrated light in a flow of nitrogen in a xenon high-flux optical furnace are presented. A scanning and transmission electron microscopes demonstrated structures of new morphologies for the powders, which were formed. XRD, Raman scattering and electron diffraction study have confirmed a complicated structure and phase composition of the powders with a prevalence of the amorphous phases. It was demonstrated an effect of experimental conditions, surface modification and additives on phase composition, morphology and structure formation. The gaseous model based on an evolution of the bubble has been confirmed new nanostructure formation. Burst of these bubbles may result in graphene-like structures formation.